Skaynam Sybele Winjall challenger4+ commander44 Software Security update

[Zeljko]

Download Winjall_ENU-6.3.0.0.zip  http://www.skynam.com/fichiers/Updates/Winjall_ENU-6.3.0.0.zip
WARNING LEVEL : Special
ALLOWS TO DISPLAY A DASHBOARD MADE OF SELECTABLE AND TUNABLE GRAPHS.
Graphical display

 
 
CONTENT
Winjall: V6.3.0.0 (new - 2nd 05/2014)
Documentations in English: Winjall User's Manual: 7 separate documents, each for one specific fonction of the software, with many didactic examples (new - 2nd 05/2014)
Nota: Does not contain any Tuneware. The Tunewares have to be downloaded and installed apart.
 
NEW FEATURES AND IMPROVEMENTS
1) Correction of uncorrect displays when working in Lambda (instead of richness as adviced):
These problems do not concern the calculations made in the ECUs but only the display by Winjall.
Some variables (with or without connection with the richness) were uncorrectly displayed when Winjall was required to work in Lambda.
- Intake or exhaust camshaft position target
- Fuel pressure target
- Tick over electrovalve position target
- Tick over electrovalve position target complementary command
- Relative difference to richness target
- Richness target complementary command
And also, when these values were the input variable of a map scale, the scales involved were incorrectly displayed.
2) For those that are using the display in Lambda:
It is important to read the new Winjall documentation "Traps and mines with Richness-Lambda display" which explains the traps when maps are used in Lambda display mode

[Zeljko]

Download Chal5_ENU-1.5.0.0.zip http://www.skynam.com/fichiers/Updates/Chal5_ENU-1.5.0.0.zip
WARNING LEVEL : Normal
 
Graphical display
 
 
NEW FEATURES AND IMPROVEMENTS
New function to test injection and ignition commands without running engine:
• allows to easily test the installation or the system working. The new document "Engine commands test" gives a full explanation of how to use this new function.
Improvement of the resynchronization in case of rpm sensor signal loss:
• If for some reason the synchronization of the ECU is lost due to a rpm sensor signal loss, the ECU re-synchronizes much faster on the engine cycle.
Significant acceleration of richness correction recovery on re-synchronization on exit of rpm sensor signal loss:
• When the synchronization of the ECU is lost due to a rpm sensor signal loss, the injection and ignition is stopped, and the richness correction is also stopped. At the ECU re-synchronization, the richness correction recovery (if richness correction is enabled) is very faster.
Powershift strain gauge switch:
• More and more gearboxes are equipped with a strain gauge switch, and no more with a On-Off switch.
This version makes much more easier the tuning of this kind of switches.
The new version of the document "sequential gearbox" explains fully how to tune them with this new firmware.
 
CONTENT
Challenger5 Tunewares:
• System V130
• Throttle/RPM: V150 (new - 31st 07/2014)
• Pressure/RPM: V150 (new - 31st 07/2014)
Documentations in English:
• Challenger5 tuning software pack: 20 separate documents, each for one specific fonction of the ECU, with many didactic examples (new - 31st 07/2014)
• Challenger5 installation: V1.12 - with commands of ignition modules (10th 01/2013)
• Challenger5 options installation: V1.10 - sequential gearboxes, air electrovalves, ... (21st 12/2011)
Nota:
• Does not contain Winjall software. Winjall must first be downloaded and installed apart.
• Does not containt the sensors convertion maps nor the actuators command maps. These maps have to be downloaded and installed apart with the pack SensAct.
 
LAST SECURITY CRITICAL MODIFICATION DONE
Not needed.

[Zeljko]

http://www.skynam.com/cms.php?id_cms=1000

CONTENT

Winjall: V9.3.0.0 (new - 04th 12/2018)
Documentations in English: Winjall User's Manual: 8 separate documents, each for one specific fonction of the software, with many didactic examples (new - 04th 12/2018)

Nota: Does not contain any Tuneware. The Tunewares have to be downloaded and installed apart by installing the ECUs.

 

NEW FEATURES AND IMPROVEMENTS

• First version to accept the new "Challenger7" ECU and the "Advance" ECUs range.
• Installs new drivers on 32 bits and 64 bits operating systems.
• Operates with Microsoft Windows XP SP3, 7, 8 and 10. 32 and 64 bits.

If you are using a CAN-USB to connect your PC to a Commander ECU, and if you haven't already upgraded it, please look at the CANUSB Update page before installing this Winjall version.





http://www.skynam.com/cms.php?id_cms=1210


NEW FEATURES AND IMPROVEMENT

Improvement of sequential gearbox management:
• Optimization of the gear upshift time (faster upshifting).
• Ignition cutoff at gear downshift (faster downshifting on strong breakings of the vehicle).
• Possibility to select the old way of shifting on slower or less precise gearboxes.
• The ECU agrees to intervene on the engine even if the gear position measurement is in error.
Read carefully new documentation for sequential gearboxes.

Significant improvement of the engine startup security (From V210)
• In the previous versions, during difficult conditions of engine start-up, the microprocessor could the capacity to perform its measurements (throttle, pressures, temperatures, ...), causing an engine stalling.
• This version prevents the loss of the measurements even in case of battery tension drop down at the engine start.

Improvement of quality and robustness of the injection command (From V200):
• When engine speed instabilities of a sufficient level (due to vibrations or else) happened, versions previous to version 200 may one or more injections, up to making thinking to a small limiter.
• The new versions never any injection (nor ignition) whichever is the engine operation.

 

CONTENT

Challenger5 Tunewares:
• System V220
• Throttle/RPM: V230 (new - 04th 12/2018)
• Pressure/RPM: V230 (new - 04th 12/2018)

Documentations in English:
• Challenger5 tuning software pack: 20 separate documents, each for one specific fonction of the ECU, with many didactic examples (new - 04th 12/2018)
• Challenger5 installation: V1.13 - with commands of ignition modules (23rd 06/2015)
• Challenger5 options installation: V1.10 - sequential gearboxes, air electrovalves, ... (21st 12/2011)

Nota:
• Does not contain Winjall software. Winjall must first be downloaded and installed apart.
• Does not containt the sensors convertion maps nor the actuators command maps. These maps have to be downloaded and installed apart with the pack SensAct.

 

LAST SECURITY CRITICAL MODIFICATION DONE

Not needed.

[Zeljko]

http://www.skynam.com/category.php?id_category=5