www.unichip.com new WEB

[Zeljko]

http://www.unichip.com/faqs.html

Dastek Unichip Products: U-Connect / Plug 'n Play, Map Select Switch, Bluetooth Module, V-tech, Driver    Nitrous Driver, Rev Limiter Module, Launch Controller, Turbo Module, X - Driver, I - Driver, EGT Unit















Version A

The Version A Unichip was the first version we ever built. It can do ignition timing and fuelling control on most older vehicles with adjustable distributors or crank sensors. It had some boost control and road-speed governor functions.

It had a white 16 pin connector and a 6 pin connector. On versions without serial numbers they were blue. On the later versions with serial numbers the serial number will start with an A.

Version B

The Version B Unichip was the second version we ever built. It can do ignition timing and fuelling control on most vehicles with crank sensors with a 60 – 2 teeth pattern (commonly know as the Bosch Motronic system). These are commonly found on most German cars and some others. It had some boost control and road-speed governor functions.

It had a white 18 pin connector and a 6 pin connector. On versions without serial numbers they were Red. On the later versions with serial numbers the serial number will start with a B.

 

Version C

The Version C Unichip was the third version we ever built. It can do ignition timing and fuelling control on most vehicles with crank sensors with a 36-1 or 36 -2 teeth pattern (as commonly found on Ford, Toyota and some Subarus). It had some boost control and road-speed governor functions.

It had a white 18 pin connector and a 6 pin connector. On versions without serial numbers they were Purple. On the later versions with serial numbers the serial number will start with a C.

Version D

Several different version D units were made ranging from D1 to D25. Almost all these have been replaced by the version Q. A very short description of each follows:

D1: Ford Falcon road speed removal unit

D2: For some older TDI vehicles with mechanical Bosch diesel pumps

D3: For some Toyota Prado/1kz-te diesel engines

D4: For some Holden Commodores

D5: For a few vehicles with air flow meters that worked with signals bigger than 5 volts. (Very limited application.)

D6: Used to convert old Rover V8 engines into electronic ignition timing control.

D7: Combination of a D6 and D5 described above. (Very limited application.)

D8: Version B with stronger fuel mixture control.

D9: Version A with stronger fuel mixture control.

D10: Version A with even stronger fuel mixture control.

D11: Version C with stronger fuel mixture control.

D12: Older Mitsubichi TDI Fuel control.

D13: Older Mitsubishi TDI injection timing control.

D15: Some Nissan Almera and Subaru from about 2001 onwards.

D19: For some Toyota Prado/1KZ-TE diesel engines.

D20: Some Mazda Miata models.

D21: Some Jeep Chrysler 6 Cyl.

D22: Diesel Nissan X-Trail.

D23: Some Hondas with 12+1 teeth on the crank sensors.

D24: Some Audi Diesels.

D25: Some VW Polo 3 cylinder TDI

[Zeljko]

LATEST NEWS read all


The latest hot we developed was the C63 Mercedes with GREAT results!  A full plug and play version for it is available. Probably the best results on a normally aspirated we have ever achieved!

On the Toyota VVTI-L we can now do the VVTI cam position as well as the lift point control.

We are the only piggyback system in the world that can do that. The customers are thrilled with the results.

On Honda we can also now do the V-tech as well as the cam position control. Good news for Honda owners!

Some more functions were added to the latest firmware file.

A new version of the map select switch will soon be available. Touch pad style and slightly lighter than the current billet aluminium version.

Then we eventually got hold of a new Nissan R35 Skyline that we will use for development and to remove the roadspeed governor on.

Watch this space!