www.quartermile.ws Forum
November 21, 2017, 07:26:15 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: e-mail: forum{et}quartermile.ws
 
   Home   Help Search Login Register Chat  
Pages: 1 2 3 [4]   Go Down
  Send this topic  |  Print  
Author Topic: Skaynam Sybele Winjall challenger4+ commander44 Software Security update  (Read 14865 times)
0 Members and 1 Guest are viewing this topic.
Zeljko
Administrator
BARBA
*****
Offline Offline

Posts: 8572


AGA


WWW
« Reply #45 on: December 01, 2014, 10:01:53 PM »

Download Winjall_ENU-6.3.0.0.zip  http://www.skynam.com/fichiers/Updates/Winjall_ENU-6.3.0.0.zip
WARNING LEVEL : Special
ALLOWS TO DISPLAY A DASHBOARD MADE OF SELECTABLE AND TUNABLE GRAPHS.
Graphical display

 
 
CONTENT
Winjall: V6.3.0.0 (new - 2nd 05/2014)
Documentations in English: Winjall User's Manual: 7 separate documents, each for one specific fonction of the software, with many didactic examples (new - 2nd 05/2014)
Nota: Does not contain any Tuneware. The Tunewares have to be downloaded and installed apart.
 
NEW FEATURES AND IMPROVEMENTS
1) Correction of uncorrect displays when working in Lambda (instead of richness as adviced):
These problems do not concern the calculations made in the ECUs but only the display by Winjall.
Some variables (with or without connection with the richness) were uncorrectly displayed when Winjall was required to work in Lambda.
- Intake or exhaust camshaft position target
- Fuel pressure target
- Tick over electrovalve position target
- Tick over electrovalve position target complementary command
- Relative difference to richness target
- Richness target complementary command
And also, when these values were the input variable of a map scale, the scales involved were incorrectly displayed.
2) For those that are using the display in Lambda:
It is important to read the new Winjall documentation "Traps and mines with Richness-Lambda display" which explains the traps when maps are used in Lambda display mode
« Last Edit: December 01, 2014, 10:05:57 PM by Zeljko » Logged

The First, DASTEK UNICHIP TECHNICALLY THE BEST; If you need more POWER, you need more AIR(cmf)
Zeljko
Administrator
BARBA
*****
Offline Offline

Posts: 8572


AGA


WWW
« Reply #46 on: December 01, 2014, 10:02:55 PM »

Download Chal5_ENU-1.5.0.0.zip http://www.skynam.com/fichiers/Updates/Chal5_ENU-1.5.0.0.zip
WARNING LEVEL : Normal
 
Graphical display
 
 
NEW FEATURES AND IMPROVEMENTS
New function to test injection and ignition commands without running engine:
allows to easily test the installation or the system working. The new document "Engine commands test" gives a full explanation of how to use this new function.
Improvement of the resynchronization in case of rpm sensor signal loss:
If for some reason the synchronization of the ECU is lost due to a rpm sensor signal loss, the ECU re-synchronizes much faster on the engine cycle.
Significant acceleration of richness correction recovery on re-synchronization on exit of rpm sensor signal loss:
When the synchronization of the ECU is lost due to a rpm sensor signal loss, the injection and ignition is stopped, and the richness correction is also stopped. At the ECU re-synchronization, the richness correction recovery (if richness correction is enabled) is very faster.
Powershift strain gauge switch:
More and more gearboxes are equipped with a strain gauge switch, and no more with a On-Off switch.
This version makes much more easier the tuning of this kind of switches.
The new version of the document "sequential gearbox" explains fully how to tune them with this new firmware.
 
CONTENT
Challenger5 Tunewares:
System V130
Throttle/RPM: V150 (new - 31st 07/2014)
Pressure/RPM: V150 (new - 31st 07/2014)
Documentations in English:
Challenger5 tuning software pack: 20 separate documents, each for one specific fonction of the ECU, with many didactic examples (new - 31st 07/2014)
Challenger5 installation: V1.12 - with commands of ignition modules (10th 01/2013)
Challenger5 options installation: V1.10 - sequential gearboxes, air electrovalves, ... (21st 12/2011)
Nota:
Does not contain Winjall software. Winjall must first be downloaded and installed apart.
Does not containt the sensors convertion maps nor the actuators command maps. These maps have to be downloaded and installed apart with the pack SensAct.
 
LAST SECURITY CRITICAL MODIFICATION DONE
Not needed.
Logged

The First, DASTEK UNICHIP TECHNICALLY THE BEST; If you need more POWER, you need more AIR(cmf)
Pages: 1 2 3 [4]   Go Up
  Send this topic  |  Print  
  Set topic sticky  
Jump to:  

Powered by SMF 1.1.13 | SMF © 2006-2011, Simple Machines LLC